Introduction:
Sand Dust Test Equipment, large observation window with bright lights to keep the box, and use of tempered glass embedded heating element. Dust test chamber provides testing as per various iec 60529 for ip5x & ip6x. Combination of various testing cycles are available in a completely mono block construction. All settings can be done in an ergonomically designed control panel with accurate and uniform dust agitation.
Sand Dust Test Equipment is applied to all mechanic, electric, electronic, electric chemical and mechanical and electric equipments, it is used to evaluate whether equipment can resistivity and storage, running or not in air of dry sand or dust. It is applied to GB 4208-2008, GB/T2423. 37-2006 and GJB150. 12A-2009.
Application: Mainly for shell protection, auto parts (light, instrument, steering system, door locks, etc. ), machinery, electrical, electronic, electrochemical and mechanical and electrical equipment, etc.
Sand Test Chamber, Dust Chamber Manufacturers XB-OTS-IP65X is according to IEC60529, IEC 60598, GB2423. 37-89 (Test L:dust test methods), GB 4208-93 protective casing grade (IP code), GB/T 4942. 2-93(protective casing grade of low-voltage apparatus), GB 7000. 1-1996, GB 7001-1986(protective casing grade of lamps), DIN40050 and IP5K0. The XB-OTS-IP65X is applied in LED or other luminaries for IP5X and IP6X test.
Working principle of chamber:
The Sand and Dust Test Chamber is a specialized testing equipment used in various industries to evaluate the ability of products to withstand extreme environmental conditions. This chamber is designed to simulate abrasive and harsh environments where sandy and dusty conditions prevail. The working principle of the Sand and Dust Test Chamber is relatively straightforward but efficient.
The chamber is composed of a testing compartment, which is connected to dust and sand generators. The testing compartment is air-tight and fitted with a viewing window for monitoring the test process. The dust and sand generators produce a controlled, reproducible amount of airborne particles that are introduced into the testing compartment using a distribution system. The air pressure inside the compartment is regulated by a blower, which ensures that the concentration of the sand and dust is kept at a predetermined level during the test.
The product under test is placed inside the testing compartment and subjected to a specific amount of sand and dust for a predetermined time frame. The product is then inspected for damage caused by the abrasive particles. The test results can be used to determine whether the product is suitable for use in sandy and dusty environments.
In conclusion, the Sand and Dust Test Chamber is a crucial testing tool that helps manufacturers ensure that their products can withstand harsh environments. Its working principle is simple but very effective in simulating abrasive and harsh environments. This equipment plays a vital role in ensuring the safety, performance, and durability of various products, including electronics, automotive parts, and industrial equipment.
Electronic and control systems:
1. The main controller LCD touch screen, can do programmable test
2. PLC complex man-machine interface control, contrived moving time, rest time and power-on time setting.
3. Multiple sets of test procedures can be planned in the interface, and each group can be arbitrarily set the desired action, easy to operate.
4. If a fault occurs in the operation of various signals are written records will be displayed to facilitate maintenance.
5. Touch the setting, digital direct display, all the conditions fully automatic locking by a microcomputer.
6. Imported electronic temperature and humidity sensor, not need to cleanup.
Specification:
|
Model |
BT-500PL |
BT-800PL |
BT-1000PL |
BT-1500PL |
|
|
Workroom size(D×W×H)mm |
800×800×800 |
800×1000×1000 |
1000×1000×1000 |
1000×1500×1000 |
|
|
Blower Time |
1S-99H(optional) |
||||
|
Vibration time |
1S-99H(optional) |
||||
|
Timing range |
0-99H |
||||
|
Dust dosage |
2-4kg/m³ |
||||
|
Dust dimensions |
<=32µm33%.32µm-250µm67% |
||||
|
Mesh Diameter |
50um |
||||
|
Wire Spacing |
75um |
||||
|
Temperature range |
25ºC-40ºC |
||||
|
Pumping time |
≤60 times ,Gas volume inner of Hull/hour |
||||
|
Pressure differential |
≤2kPa(20mbar) |
||||
Customer support services:
1. Installation
2. Training (Training customer employees)
3. Calibration
4. Preventative maintenance
5. Replacement parts
6. Assistance via phone or internet
7. On-site diagnosis and repair/online diagnosis and repair
DustProof Test Equipment IEC 60529 Sand Dust Climatic Test Chamber are made for the simulation of dust and sand conditions. These dust test chambers are used to test the exposure of test the exposure of automotive and electronic components under extreme environmental conditions in order to validate product seal. Dust ingress test methods included IEC60529, ISO20653 and many others.
FAQ
1. Do you offer after-sales service? How can I ask for that? And how about the warranty?
Every machine from our factory has a 14-month warranty after shipment. Generally, we offer 12 months for the FREE maintenance, while considering of sea transportation, we can extend 2 months for our customers.
If your machine doesn't work, you can send E-mail to us and we will try our best to find the problem by email or skype video chat if neccesary. After confirmation of the problem, we can send you new spare parts or provide on-site repair.
2. What's the delivery term?
At most of time, we have stock in the factory. If there is no stock, normally, the delivery time is 15-20 working days after deposit receipt. If you are in urgent need, we can consider making a special arrangement for you.
3. Do you accept customization service? Can I have my logo on the machine?
Yes, of course. We can not only offer standard machines, but also customized machines according to your requirements. And we can also put your logo on the machine.
4. How to install and use the product?
We will send you operating instructions, English video by Email. Or you can download on our officail website directly.
Most of our machine is shipped with a whole part, which means it is already installed, all you need to do is to connect the power cable and start to use. And if possible, we can also install your machine at site.
Hot Tags: sand and dust test chamber forlab testing, China, suppliers, manufacturers, factory, buy, cheap, Auto Parts Test Equipment, Ozone corrosion testing chamber, IPX12 rain waterproof Test Chamber, Auto parts test machine, Overall Testing System, PCB Semiconductor
